Monoshock or twin shocks: your bike decides

You are looking for new shocks for your bike and two words keep coming up: monoshock and twin shocks. It looks like a choice. Usually it is not. Your bike already has a system, and you buy the shock that goes with it. Here you read how both work, where they differ and how to tell what sits under your bike.
Two shocks or one
With twin shocks there is a shock on the left and on the right of the swingarm. Each shock is a spring and a damper unit. One eye mounts to the frame, the other to the swingarm. Together they carry the weight of bike, rider and luggage.
With a monoshock, one shock does that job. It sits in one place between frame and swingarm, on one side or in the middle under the seat. One spring, one damper unit, one set of mounts.
The job is the same. The spring carries the weight and soaks up bumps. The damping slows the spring down, so the bike does not keep bouncing after a bump. The difference is in how that work is spread over frame and swingarm.
How twin shocks work
Twin shocks are the classic system. On most classic bikes they sit directly between frame and swingarm, with no linkage in between. What the rear wheel does, the shock feels almost one to one.
What that means in practice:
- The load is spread over two shocks and four mounting points.
- Preload is easy to reach. On many twin shocks you set it from the outside.
- Both shocks have to work exactly the same. A difference between left and right makes the swingarm twist. That is why you always replace twin shocks as a pair.
- There is little room for a big reservoir or a lot of travel. On a classic boxer that is no problem, the bike was not built for it.
- It suits the look of a classic. On many custom builds that is a reason in itself.
In the shop you find them under twin shocks.
How a monoshock works
With a monoshock, one shock carries everything. That asks for strong mounts on frame and swingarm. It also gives you something back.
- You set up one shock instead of two. A difference between left and right is not possible.
- There is often room for a shock with more adjustment or a separate reservoir.
- The swingarm can be built differently, for example single sided, the way BMW does it.
- The shock is specific to the model. Mounts, length and travel have to match exactly.
Monoshocks are in the shop under mono shocks.
What BMW did: twin shock, Monolever and Paralever
With BMW you can follow the history of the rear suspension quite well. That helps when you want to know what sits under your bike.
The boxers of the /5, /6 and /7 series run on twin shocks. Think of an R100/7 or an R75/6. The R80 RT and the R100 RS and RT from before about 1984 also have two rear shocks.
In 1980 the Monolever arrived, first on the R80 G/S and from the mid eighties on the road boxers too. It is a single sided swingarm with the drive shaft inside and one shock. An R80 Monolever is an example.
At the end of the eighties the Paralever followed on the GS models, and later on the R80 R and R100 R. That swingarm has an extra rod that takes up the reaction of the shaft drive. Here too there is one shock, as on the R100 GS Paralever.
The K series started with a Monolever and one shock, as on the K75 and the K100. Later K models, such as the K100 RS 16V and the K1100, got a Paralever. They also have one shock.
The lengths in our catalogue show how different this turns out. Twin shocks for the older boxers sit around 320 to 340 mm. A shock for a Monolever boxer is around 410 mm, and on the Paralever boxers it goes up to 475 or 495 mm. On the K series you see 305, 350 and 385 mm. So you cannot just fit the shock of one model on another.
Your bike decides, not your preference
This is the core. A bike with two rear shocks gets a pair of twin shocks. A bike with one gets a monoshock. Frame and swingarm are built for it: the mounting points, the angles and the travel.
Not sure what you have? Look at the back of your bike. If you see a shock on the left and on the right between frame and swingarm, you have twin shocks. If you see one, often next to the drive shaft or under the seat, you have a monoshock. Or pick your bike on the shock absorber page. You then only see the shocks that fit.
Converting from twin to mono
Some riders want to switch systems, usually for the line of a custom build. That is not a matter of ordering a different shock. You rebuild the rear of the bike. Frame or swingarm change too, and that also affects road approval.
Want to know whether such a conversion is worth it? Read the blog on a monoshock conversion for the BMW K series. It explains what is involved.
YSS or Hagon
Once you know which system you have, the question is which shock. At Dapper Motor you choose YSS from the range or build a Hagon to measure. How to choose between them is in YSS or Hagon: which shock suits your motorcycle?.
You find the range per brand on the YSS brand page and the Hagon brand page.
Measure first, then choose
If you replace an existing shock, measure first. Measure the length from the centre of one mounting eye to the centre of the other, preferably on the shock that is on the bike now. Also check the top and bottom mounts. The measuring guide shows how.
Then you choose. In the shock configurator you pick your bike and see which shocks belong on it, YSS and Hagon side by side.
Pick your bike and see what fits. Still not sure? Send us your model and year and we will take a look.
Products for this article
Frequently asked questions
Can I replace twin shocks with a monoshock?+
Not with just a different shock. Frame and swingarm are built for the system that is fitted. Switching means rebuilding the rear of the bike, and that also affects road approval.
What is the difference between Monolever and Paralever?+
Both are single sided BMW swingarms with one shock. The Paralever has an extra rod that takes up the reaction of the shaft drive. The shocks differ in length and mounts, so always choose by your own model.
How can I tell which system my bike has?+
Look at the rear. A shock on each side of the swingarm means twin shocks, one shock means a monoshock. You can also pick your bike on the shock absorber page and see only what fits.





