~ Where passion meets precision · Atelier Haarlem since 2010 ~
Traditional incandescent bulbs draw more electrical current than LEDs. Your motorcycle's flasher relay is calibrated for this higher current draw. When you switch to LEDs, the lower current causes the flasher to cycle too rapidly. A load equalizer mimics the electrical load of incandescent bulbs, restoring the correct flash rate.
Yes, the MCS Universal Load Equalizer Set features universal fitment, making it compatible with virtually all 12V motorcycle electrical systems. Whether you ride a BMW classic, cafe racer, or any custom build, this equalizer will work with your LED conversion. However, always verify your motorcycle uses a 12V system before installation.
Load equalizers generate significant heat during operation because they work by converting electrical energy into thermal energy to simulate bulb resistance. This is why prolonged continuous use is not recommended. The 25W power draw means heat dissipation is substantial. For safety, avoid using turn signals for extended periods and always check the unit for excessive heat buildup.
No, you should never operate 4-way flashers (hazard lights) with load equalizers installed. The continuous operation of all four turn signals simultaneously creates excessive heat that can damage the equalizer or pose a fire risk. Always remove the load equalizers before using your 4-way flashers.
The 6.8 Ohm resistance rating indicates the electrical resistance the load equalizer provides. This resistance value is specifically calibrated to simulate the load characteristics of traditional incandescent turn signal bulbs, ensuring your flasher relay cycles at the correct frequency. This is a critical specification for proper LED turn signal operation.
Installation involves connecting the load equalizer in parallel with your LED turn signals in the electrical circuit. Typically, this means wiring it between the turn signal flasher relay and the LED turn signal bulbs. Detailed installation instructions should accompany your kit. If you're uncomfortable with electrical work, consult a qualified motorcycle technician to ensure safe and correct installation.
Yes, the load equalizer can work with partial LED conversions where you've upgraded only some turn signals. However, you may need to adjust the number of equalizers or their wiring configuration depending on which signals are LED and which remain incandescent. Consult the specific instructions for your setup to ensure correct operation.
Load equalizers are passive electronic components without moving parts, so they have no specific lifespan in the traditional sense. However, heat exposure and continuous use can degrade them over time. If your turn signals stop flashing at the correct rate after installation, the equalizer may have failed and require replacement. Regular inspection for heat damage is recommended.
More questions? View all FAQs
Converting your classic motorcycle to LED turn signals? The MCS Universal Load Equalizer Set is the essential solution to maintain proper turn signal flash rates. When upgrading from traditional incandescent bulbs to energy-efficient LEDs, your bike's electrical system may flash too rapidly.
This load equalizer corrects that issue by mimicking the electrical load of conventional bulbs, ensuring your turn signals operate at the correct frequency.
Designed for universal fitment, this load equalizer set is perfect for cafe racer builds, BMW classic restorations, and any custom motorcycle project. Each unit draws 25W and features a 6.8 Ohm resistance rating. Installation is straightforward, making it an ideal addition to your LED conversion upgrade without requiring complex rewiring or modifications.
Please note: Load equalizers generate heat during operation. Avoid prolonged continuous use of turn signals, and never operate 4-way flashers with load equalizers installed, as this may cause overheating. For optimal performance and safety, remove equalizers before extended flasher use.
Converting your classic motorcycle to LED turn signals? The MCS Universal Load Equalizer Set is the essential solution to maintain proper turn signal flash rates. When upgrading from traditional incandescent bulbs to energy-efficient LEDs, your bike's electrical system may flash too rapidly.
This load equalizer corrects that issue by mimicking the electrical load of conventional bulbs, ensuring your turn signals operate at the correct frequency.
Designed for universal fitment, this load equalizer set is perfect for cafe racer builds, BMW classic restorations, and any custom motorcycle project. Each unit draws 25W and features a 6.8 Ohm resistance rating. Installation is straightforward, making it an ideal addition to your LED conversion upgrade without requiring complex rewiring or modifications.
Please note: Load equalizers generate heat during operation. Avoid prolonged continuous use of turn signals, and never operate 4-way flashers with load equalizers installed, as this may cause overheating. For optimal performance and safety, remove equalizers before extended flasher use.
Delivery time: 3–5 business days
Be the first to review this product
